Bending of Sawn Wood Products Obtained from Conventional Sawing and Parallel to Generatrix Sawing

Vladimir Glukhikh, Olga Khrabrova

Abstract


This paper considers bending of sawn wood products obtained from logs by conventional sawing and sawing parallel to generatrix. Issues related to strength and stiffness of sawn wood products sawn parallel to generatrix have not being studied yet, thus such issues are of practical and scientific interest. Earlier our investigation dealt with changes in tilting angle of wood fiber of sawn wood materials obtained from logs by conventional sawing and sawing parallel to log generatrix.

This concept is used for generating of mathematical models describing changes in elasticity modulus across the wood plank width which enables to foresee the wood plank bending strength and stiffness.

The proposed procedure allows for the evaluation of wood planks bending stresses occurred when various log sawing schemes were used. Wood planks bending value is calculated to cover the difference between stiffness of wood planks obtained at the implementation of both sawing schemes.

The investigation results are not only of scientific interest, but are also of practical interest in terms of construction and fabrication of laminated wood structures, wood structural panels etc.


Keywords


Bending; stiffness; elasticity modulus; stresses; strength

Full Text:

PDF

References


Akishenkov S. I. (1980) O pokazatelyakh kachestva sushki pilomaterialov. [On sawn wood products drying quality]. IN Аktual'nye napravleniya razvitiya sushki drevesiny: Tezisy dokladov Vsesoyuznoj konferentsii. TSNIIMOD [Current approaches to wood drying development: All-Soviet Union conference abstracts. Central Scientific-Research Institute of Wood Machining], Arkhangelsk, pp. 100–101

Ashkenazi E. K. (1978) Anizotropiya drevesiny i drevesnykh materialov. [Anisotropy of wood and wood materials]. Forest industry, Moscow, USSR

Glukhikh V. N. (2007) Anizotropiya drevesiny kak faktor dlya povysheniya kachestva sushki pilomaterialov. [Anisotropy of wood as a driver of sawn wood products drying improvement]. Publishing office of St. Petersburg University, Saint Petersburg, Russia

Glukhikh V. N. (2004) Napryazheniya v tsilindricheski anizotropnoy polose, nagruzhennoy poperechnoy siloy na kontsakh. [Stresses in cylindrical anisotropy strip under transverse loading force at the ends]. Izvestiya SPbLTA [News of Saint Petersburg Forest Engineering Academy], Issue 171: 158–165

Glukhikh V. N., Zaripov Sh. G. (2008) Poperechnoe koroblenie pilomaterialov pri sushke. [Transverse distortion of sawn wood products at drying]. Izvestiya SPbLTA [News of Saint Petersburg Forest Engineering Academy], Issue 181: 179–186

Glukhikh V. N., Khrabrova O. Yu, Akopyan A. L (2013) Postoyannye uprugosti pilomaterialov pri raspilovke breven parallel'no obrazuyushchey. [Constant elasticity of sawn wood materials at sawing of logs in direction parallel to generatrix]. Izvestiya SPbLTA [News of Saint Petersburg Forest Engineering Academy], Issue 203: 117–127

Glukhikh V. N., Chernykh A. G. (2013) Anizotropiya drevesiny. Tekhnologicheskiy aspect. [Anisotropy of wood. Processing aspect]. Saint Petersburg State University of Architecture and Civil Engineering, Saint Petersburg, Russia

Kolenchuk K. I. (1950) Poperechnoe koroblenie drevesiny [Wood transverse distortion]. IN Sbornik trudov instituta stroitel'noi mekhaniki AN USSR [Collection of paperworks, Institute of Structural Mechanics of Academy of Sciences of the Ukrainian SSR]: # 12

Lekhnitskiy S. G. (1957) Anizotropnye plastinki. [Anisotropic plates]. Gostechizdat, Moscow, USSR

Lyulenko V. N. (1967) Issledovanie vliyaniya nekotorykh faktorov na velichinu koroblenniya [Investigation of some drivers effect over distortion value]. PhD thesis, Leningrad, USSR

Petrukhin G. G. (1970) Koroblenie pilomaterialov pri mekhanicheskoy obrabotke [Sawn wood products machining distortion]. IN Sbornik rabot: MLTI [Collection of papers: Moscow Forest Engineering Institute]: # 35

Petrukhin G. G. (1970) Koroblenie poperechnykh secheniy derevyannykh elementov. [Distortion of wooden elements cross sections]. IN Sbornik rabot: MLTI [Collection of papers: Moscow Forest Engineering Institute]: # 35

Skripal'shchikova N. F. (1975) Issledovaniya i metod snizheniya korobleniya pilomaterialov vo vremya kamernoy sushki. [Investigations and method of sawn wood products distortion decrease at kiln drying]. IN Sushka drevesiny: Materialy Vsesoyuznogo nauchno-tekhnicheskogo soveshchaniya. TsNIIMOD [Wood drying: Paperwork of All-Soviet Union Scientific and Research Meeting Central Scientific-Research Institute of Wood Machining]. Arkhangelsk, USSR, p. 67

Sokolov P. V, Glukhikh V. N (1971) Vliyanie nekotorykh faktorov na silu korobleniya drevesiny. [Effect of some drivers on wood distortion forces]. Derevoobrabatyvayushchaya promyshlennost' [Wood-working industry], # 3

Strikha I. A. (1974) Prichina deformatsiy detaley iz drevesiny i sposoby ee umen'sheniya. [Causes of wooden parts deformation and ways of its decrease]. Derevoobrabatyvayushchaya i lesokhimicheskaya promyshlennost' [Wood-working and wood chemical industry], # 7.

Sukhova A. V. (1958) K voprosu o poperechnykh korobleniyakh drevesiny. [On wood transverse distortion]. Khimki.




DOI: https://doi.org/10.23968/2500-0055-2016-1-1-4-9

Refbacks

  • There are currently no refbacks.




     

ISSN: 2500-0055