ANALYSIS OF BENDING STEEL FIBER REINFORCED CONCRETE ELEMENTS WITH A STRESS-STRAIN MODEL

Aleksey Pavlov, Aleksey Khegay, Tatyana Khegay

Abstract


Introduction: Fiber concrete is a complex composite material with unique properties. Its behavior is accounted for in steel fiber reinforced concrete elements using simplified stress-strain models. The article describes an approach to the analysis of bending steel fiber reinforced concrete elements using stress-strain diagrams for compression and tension. Purpose of the study: The study is aimed to develop a method for the analysis of bending steel fiber reinforced concrete elements using stress-strain diagrams that will be simpler than the existing ones. Methods: The study is based on the traditional principles of the analysis of reinforced concrete structures. The method applied is described through equations for the equilibrium of forces affecting the longitudinal axis of the element and the ultimate bending moment. Internal forces in the element cross-section are expressed as relative strains whose diagram is nearly linear in accordance with the Bernoulli’s hypothesis. Results: We present final equations to determine the load-carrying capacity of a bending element by standard cross-sections. The values of strength and stress-strain properties of fiber reinforced concrete and reinforcement serve as the source data for the calculations.

Keywords


Fiber concrete, steel fiber reinforced concrete, non-linear stress-strain model, fiber reinforced concrete and reinforcement stress-strain diagrams, relative strains.

Full Text:

PDF

References


Ashour, S. A. and Wafa, F. F. (1993). Flexural behavior of high-strength fiber reinforced concrete beams. ACI Structural Journal, 90 (3), pp. 279–287.

Bakhotskiy, I. V. (2013). Experimental and theoretical investigations of stress-strain behavior of fiber-reinforced concrete members exposed to bending with torsion. Bulletin of Civil Engineers, 4, pp. 48–53.

Brandt, A. M. (2008). Fibre reinforced cement-based (FRC) composites after over 40 years of development in building and civil engineering. Composite Structures, 86 (1–3), pp. 3–9. DOI: 10.1016/J.COMPSTRUCT.2008.03.006.

British Standards Institute (2005). BS EN 14651:2005+A1:2007. Test method for metallic fibre concrete – Measuring the flexural tensile strength (limit of proportionality (LOP), residual), 20 p.

Eryshev, V. A. (2018). Deformation method for calculating the strength of reinforced concrete bending elements using deforming diagrams for elastoplastic materials. Systems. Methods. Technologies, 1, pp. 79–84. DOI: 10.18324/2077-5415-2018-1-79-84.

Evdokimova, T. S. (2017). Stress-strain behavior and strength analysis of fiber-reinforced concrete elements subjected to skew bending. PhD Thesis in Engineering. Saint Petersburg: Saint Petersburg State University of Architecture and Civil Engineering.

Evseyev, E. N. (2012). Testing of fiber according to European standards. Concrete Technologies, 5–6, pp. 31–32.

Karpenko, S. N. (2010). Reinforced concrete stress-strain models in increments and structural analysis methods. DSc Thesis in Engineering. Moscow: Research Institute of Construction Physics of the Russian Academy of Architecture and Construction Sciences.

Ministry of Construction Industry, Housing and Utilities Sector of the Russian Federation (2018). Regulations SP 360.1325800.2017. Steel fiber reinforced concrete structures. Design rules. Moscow: Standartinform, 70 p.

Ministry of Construction Industry, Housing and Utilities Sector of the Russian Federation (2019). Regulations SP 63.13330.2018. Concrete and reinforced concrete structures. General provisions. Revised edition of SNiP 52-01-2003. Moscow: Standartinform, 143 p.

Morozov, V., Khegai, A., Evdokimova, T. and Opbul, E. (2016). Experimental diagrams of fiber concrete straining under tension and compression and their implementation in calculation of bearing capacity of fiber-reinforced concrete flexural elements. Materials Science Forum, 871, pp. 160–165. DOI: 10.4028/www.scientific.net/MSF.871.160.

National Association of Builders (2015). Corporate Standard STO NOSTROY 2.27.125-2013. Underground space development. Structures of transport tunnels made of fiber-reinforced concrete. Design and construction rules. Moscow: Ordzhonikidze Central Institute of Standard Design, 104 p.

Rak, N. A. (2011). A method of structural analysis for steel fiber reinforced concrete structures using steel fiber reinforced concrete and bar reinforcement stress-strain diagrams. In: Proceedings of the 3rd International Symposium “Issues of Modern Concrete and Reinforced Concrete”. Minsk.

Talantova, K. V. and Mikheyev, N. M. (2014). Steel fiber concrete and constructions based thereon. Saint Petersburg: Emperor Alexander I St. Petersburg State Transport University, 275 p.

Valente, T., Gonçalves, D., Lourenço, L., Costa, I. and Barros, J. (2017). Fiber reinforced concrete. Concrete Goods and Constructions, pp. 54–62.

Vorontsova, N. S. (2017). Experimental investigations of fiber reinforced concrete members subjected to biaxial bending. Bulletin of Civil Engineers, 4, pp. 66–71. DOI: 10.23968/1999-5571-2017-14-4-66-71.

Zhavoronkov, M. I. (2017). Developing methods for the determination of fiber-reinforced concrete crack resistance characteristics. PhD Thesis in Engineering. Saint Petersburg: Saint Petersburg State University of Architecture and Civil Engineering.




DOI: https://doi.org/10.23968/2500-0055-2020-5-3-14-21

Refbacks

  • There are currently no refbacks.




     

ISSN: 2500-0055